Stolit MP Render: A Freestyle Finishing Render for Bespoke Facades
Last updated 17 November 2026

Stolit MP render is Sto's freestyle finishing render: an organic, water-dilutable topcoat that an applicator works by hand into a fine, custom texture. Engineered in Germany and supplied by Sto Australia, it is designed for architects, specifiers and builders who want a bespoke facade finish rather than a set pattern, with a wide choice of colour.
This page covers what Stolit MP is, how its texture is created, the colours available, and how it is applied. To compare it with the rest of the range, see our Sto finishing renders overview, or go straight to the Stolit MP technical data sheet.
What is Stolit MP render?
Stolit MP is an organic finishing render supplied as a free-style textured render, and Sto's brochure describes it as its freestyle special effect render. It contains high-quality marble grains from natural deposits, and it arrives ready to use in a 25kg pail, tinted to your chosen colour. Applied over a Sto base coat, it forms the final, visible layer of the facade: the layer that carries the colour, sets the texture and takes the weather.
Stolit MP is highly water-repellent and weather-resistant, and it is highly permeable to water vapour, so the wall can breathe while the surface sheds water. What sets it apart from the rest of the Stolit range is that its pattern is not fixed by a grain size. The texture is created by how the render is worked, which is why it suits a design that calls for something custom.
A freestyle textured render, worked by hand
Stolit MP is applied evenly with a steel trowel at a layer thickness of at least 1mm, and up to 5mm in places. The texture is then created by hand, using whichever tool suits the design: a plastering trowel, a brush, a texturing roller, a bucket trowel, a spatula or a sponge. The same material can be rubbed up to a near-smooth surface or worked into a more pronounced pattern, so one product can deliver a range of looks across a project.

That freedom makes Stolit MP a bespoke render finish rather than a catalogue one. It also means the result depends on the applicator. Sto describes the freestyle technique as a specialist one that calls for highly skilled applicators, so talk to a Sto consultant early, and ask for a site sample so the texture, shade and technique are agreed before work begins.
A float-finished render for a fine look
Where the brief calls for a fine surface, Stolit MP can be finished as a float-finished render. Sto's technical data sheet sets out a two-step approach. First, a stippled finishing render in 1.5mm grain is trowelled onto the prepared substrate and lightly trowelled off; excess paste and grains are worked into the surface with a plastic trowel, and once dry, protruding grain tips are removed with a wide spatula. Second, Stolit MP is applied in an even layer about 1mm thick, left briefly to harden, then float-finished evenly with a latex sponge float that is moistened regularly with water.
Float-finished or washed fine textured surfaces offer less protection from algae and fungus than a coarser texture, so Sto recommends a double coat of facade paint to protect the surface optimally. A double coat may also be needed to even out the colour shade. Plan for both at specification stage.
A coloured finishing render, tinted from the StoColor System
Stolit MP is supplied white and tinted to colour. It can be tinted to any shade in the StoColor System, an 800-colour architectural palette, and is also available on request in a wide range of other shades.
Three points are worth settling at specification stage. First, where the chosen shade has a light reflectance value of 15 or more, Sto's data sheet says no additional finish is necessary; for intense or very dark shades, additional paint coats improve colour stability, because weathering, UV radiation and moisture can change colour over time. Second, the texturing grain is natural white marble, so its natural graining can show as darker flecks, and in light, clear yellow shades the grain colour can read through across an area. This is a property of a marble-filled render rather than a defect. Third, uneven substrate absorbency, different moisture levels across an area, very different alkalinity in the substrate and direct sunlight on a still-damp coating can all affect colour accuracy, so they should be avoided on site.
Where Stolit MP is used
Stolit MP is an exterior finishing render. It is applied over a Sto base coat on masonry, insulated and rainscreen cladding facades, on both mineral and organic substrates. In practice it is specified as the finishing layer of a Sto render system: the substrate and base coat are chosen first, and Stolit MP is selected to suit. Browse our Sto render systems by construction type.
Stolit MP is not designed for horizontal or sloping surfaces that are exposed to weathering, where water would otherwise sit on the surface. Sto's render systems are BRANZ appraised, and appraisal coverage is specific to each system and substrate, so confirm with a Sto consultant which appraisal applies to your project.
Stolit MP technical performance
The figures below come from Sto's Stolit MP technical data sheet. They are average values, and because the render uses natural raw materials they can vary slightly between batches without affecting suitability. The test methods are European (EN) standards, as published by the manufacturer.
| Property | Value | Test method / note |
|---|---|---|
| Pack size | 25kg pail | — |
| Colour | White, tinted to the StoColor System | — |
| Texture | Freestyle, worked by hand; fine to custom | — |
| Density | 1.7–1.9 g/cm³ | EN ISO 2811 |
| Water permeability rate (w) | Less than 0.05 kg/(m²·h0.5), class W3 (low) | EN 1062-1 |
| Water vapour diffusion-equivalent air layer thickness (sd) | 0.28–0.33m, class V2 (medium) | EN ISO 7783 |
| Layer thickness | Minimum 1mm, in places up to 5mm | Depends on the desired texture |
| Approximate consumption | Thin layer: 1.50 kg/m² · medium layer: 2.50 kg/m² · thick layer: 4.00 kg/m² | Guide only; depends on substrate, application and consistency |
| Application temperature | +5 °C to +30 °C (substrate and air) | Not in intense direct sunlight or onto heated substrates |
| Overcoating | After 24 hours at the earliest | At about 20 °C and 65% relative humidity |
Scroll sideways to see the full table.
In plain terms, the low water permeability rate shows that the surface resists liquid water, while the medium vapour class means moisture vapour can still pass through the wall. When Stolit MP is combined with a StoTherm insulation system, it also offers shockproof, crack-resistant performance.
Applying Stolit MP
Stolit MP is applied by trained Sto-registered applicators over a prepared base. The substrate must be firm, dry, clean and load-bearing, and free of sinter layers, efflorescence and release agents; damp or not fully cured substrates can cause bubbling and cracking in the coating. Existing coatings must be checked, and any that are not load-bearing removed. On mineral substrates, Sto recommends an absorbency-equalising, adhesion-promoting intermediate coat, and leaving it out can affect both application and appearance. If Stolit MP is used as a thin-layer, float-finished fine textured render, additional levelling coats of substrate filler are needed.
The render goes on by hand or by machine, and the freshly applied render normally has to be reworked by hand to achieve the intended texture. It should be diluted with as little water as possible, because too much dilution impairs application, hiding power and colour intensity. On larger surfaces, skin formation should be expected, and trapped air can cause blisters, so the render should only be modelled with dry tools.
Stolit MP is applied between +5 °C and +30 °C at the substrate and in the air, out of intense direct sunlight and never onto heated substrates. Strong air movement during application and early drying can increase shrinkage cracks and pores. At around 20 °C and 65% relative humidity it can be overcoated after 24 hours at the earliest; layers thicker than 2mm, higher humidity, condensation, low temperatures and low air exchange can lengthen that. Freshly rendered facades should be protected from rain until they are dry.
Stolit MP data sheets and downloads
The technical data sheet, the material safety data sheet and the sustainability data sheet for Stolit MP are available below. Please check that you are working from the current versions before you specify, and contact Sto Australia if you need help finding the right document for your project.
Stolit MP in the Sto finishing range
Stolit MP is part of a range of coloured finishing renders that Sto has refined for decades, engineered in Germany by a group with ISO 9001 and ISO 14001 certified management systems. Within the same family, Stolit K render gets its stippled pattern from its grain size, and Stolit Milano render is a very fine, smooth-looking, sandable finish. Stolit MP is the one to consider when the design calls for a hand-worked, customised texture.
Specify Stolit MP with Sto Australia
Sto Australia's technical consultants can help you choose a texture, check shade suitability and match Stolit MP to your substrate and render system, with plan review and mock-up assistance available. Tell us about your substrate, elevation and preferred shade, and a consultant will respond during business hours, Monday to Friday, 7:00am to 3:30pm. Request a quote or call +61 3 9768 4900.
Frequently asked questions
What is Stolit MP used for?
Stolit MP is the coloured, hand-worked topcoat of a Sto render system on exterior facades. It is applied over a Sto base coat on masonry, insulated and rainscreen cladding facades, and it provides the colour, a custom texture and much of the weather protection. It is not a paint, and it is not intended for horizontal or sloping surfaces exposed to weathering.
How do I choose between Stolit MP, Stolit K and Stolit Milano?
The choice is mainly about how the texture is made. Stolit K gets its stippled pattern from its grain size, Stolit MP is worked by hand into a fine or custom texture, and Stolit Milano is a very fine, smooth-looking and sandable finish. You can compare all three on the Sto finishing renders page, and a Sto consultant can help you match a texture to your design.
Does Stolit MP need a skilled applicator?
Yes. Sto describes the freestyle technique as a specialist one that calls for highly skilled applicators, because the finished texture depends on how the render is worked. Stolit MP is applied by trained Sto-registered applicators, and a site sample helps everyone agree the result before the main work begins.
Can Stolit MP be tinted to any colour?
Stolit MP can be tinted to any shade in the StoColor System, and is also available on request in a wide range of other shades. Strong colours can change with weathering and UV exposure, and additional paint coats improve their colour stability. On float-finished fine textured surfaces, a double paint coat may be needed to even out the colour shade.
How long before Stolit MP can be overcoated?
At about 20 °C and 65% relative humidity, Stolit MP can be overcoated after 24 hours at the earliest. Thicker layers, higher humidity, condensation, low temperatures and poor air exchange can all slow drying, so allow extra time in cool or damp conditions, and protect the facade from rain while it dries.

